Wireless

S-C53DLC40D is a singlemode 1.25G SFP CWDM module with a 1530nm wavelength and two LC connectors for connection up to 40km. CWDM in your network will allow you to Increase efficiency of existing fiber network Prov

S-C57DLC40D is a singlemode 1.25G SFP CWDM module with a 1570nm wavelength and two LC connectors for connection up to 40km. CWDM in your network will allow you to Increase efficiency of existing fiber network Prov

S-C59DLC40D is a singlemode 1.25G SFP CWDM module with a 1590nm wavelength and two LC connectors for connection up to 40km. CWDM in your network will allow you to Increase efficiency of existing fiber network Prov

S-C61DLC40D is a singlemode 1.25G SFP CWDM module with a 1610nm wavelength and two LC connectors for connection up to 40km. CWDM in your network will allow you to Increase efficiency of existing fiber network Prov

The S-4554LC80D is sold as a kit of two single mode WDM modules with Gigabit speed, one LC connector on each side and maximum distance up to 80km. The wavelengths of the modules are 1490 / 1550nm and 1550 / 1490nm.

We are now offering a Hot Swap -48V DC telecom power supply (product code PW48V-12V150W), available to purchase separately for use with CCR1072. Simply remove one of the current power supplies and replace with the new PW48V-12V150W for -48V installatio

Smallest outdoor series model - a fully featured wireless RouterBOARD powered by RouterOS. Weatherproof, durable and ready to use. Now with 802.11ac support, a Gigabit Ethernet port and a selectable wireless band (2.4GHz or 5GHz, up to 80 MHz wide chan

CA411-711 is new indoor case for RB411, RB911, RB912 and RB922 series. It has changeable front panels, so you can choose one that fits the product that you actually use. Also, case is higher to accommodate high-power wireless cards and has wall mountin

12POW150 is replacement Hot Swap power source for MikroTik CCR1072-1G-8S+. Total output power is 150W.

The quickMOUNT extra is a advanced wall mount adapter for large point to point and sector antennas. You can mount it on the wall or use it as an adapter from large diameter pole to small size antenna mounting clip ensuring reliable fitment. T

mANT30 is a professional class 5 GHz 30dBi dish antenna, built to the highest industry standards. Built to seamlessly accomodate our Basebox series products, but can be used for any pole mounted wireless device due to the adequate length of the include

It reduces wind load, protects reflector surfaces from harsh environment, protects the antenna feed from falling objects, as well as positively affects the antenna sustainability and operational life. It's made from a special material that has a low di

It reduces wind load, protects reflector surfaces from harsh environment, protects the antenna feed from falling objects, as well as positively affects the antenna sustainability and operational life. It's made from a special material that has a low di

The PowerBOX is an outdoor five Ethernet port router with PoE output on four ports. You can use this device to supply power to four PoE capable devices such as our SXT or others. Since the device has a waterproof outdoor case, you can mount i

CA150 is a mounting box from MikroTik for indoor use and is intended only for MikroTik RouterBOARD models RB450, RB450G and RB850Gx2. There are molded holes for 5 Ethernet ports on the side and a hole for the power jack and RS232 seri

Replacement holder for RouterBOARD SXT models. Suitable for all models.

R11e-2HnD is a Low-profile Lower power version of our 2.4Ghz miniPCIe card - it has a small heat-sink, u.Fl connector and less output power (800mW). Low profile is useful if you need to install the card in device like a laptop.

The license key for your installed RouterOS on RouterBOARD or x86 platform. Differences between different levels of license, we recommend you take a look here.

The license key for your installed RouterOS on RouterBOARD or x86 platform. Differences between different levels of license, we recommend you take a look here.

The license key for your installed RouterOS on RouterBOARD or x86 platform. Differences between different levels of license, we recommend you take a look here.

It is a special key which is issued by the Support Team if you accidently lose the license, and the Mikrotik Support decides that it is not directly your fault. This key has the same features as the key that you lose. Note that before issuing such key,

Replacement 500 W power supply for MikroTik CRS328-24P-4S+RM PoE switch.

LoRa omnidirectional antenna with 6.5 dBi gain for the frequency band 900 to 928 MHz with one SMA female connector and IP66 protection. The package includes a removable 1m long pigtail with SMA male

KNOT is a truly universal device with a wide range of connection options and support for protocols and interfaces. It is an IoT Gateway that uses LoRa technology (902 - 928 MHz) but also Narrow Band and CAT-M b>, which a

FTC11XG is a 10Gbps fiber-to-metal converter with an implemented switch-chip, SwOS Lite management (VLAN support, LAG, IGMP, SNMP, ACL, traffic shaping...) in outdoor design with IP55 protection. This converter has one Gigabit LAN port wi

LtAP LR8 LTE kit (2024) equipped with a new LTE modem is a compact and robust wireless access point with support for LTE Cat6, LoRa network, LAN, GPS, USB and serial port for debugging. The perfect device for noisy urban environments as well as

The XQ+CM0000-XS+ adapter is the perfect accessory for CR504, CRS518, CRS510 switches and other devices with QSFP28 (100Gbps) or QSFP+ (40Gbps) ports. Thanks to this adapter, lower speed modules can be used in higher speed slots. If you do not c

Welcome to the forefront of networking: the future-proof CRS520-4XS-16XQ-RM with extra processing power, 4 GB of DDR4 RAM, and the best price per 100 Gigabit port we’ve seen so far. With 16x 100 Gigabit QSFP28 ports, 4

XS+85LC01D is a multimode SFP/SFP+SFP28 module with a maximum throughput of 25 Gbps, supporting lower speeds of 1 Gbps and 10 Gbps with a wavelength of 850 nm and two LC connectors for connections up to a distance of 100 m. The mod

Hot-swap 54.5V 10.35A power supply for the CRS320-8P-8B-4S+RM PoE++ switch. The switch comes with a single 600W PSU and an expansion slot for a second PSU that can raise the total power output all the way to 1150 Watts,