Accessories

The new MikroTik Gigabit PoE adapter for powering any RouterBOARD over Gigabit Ethernet. Simply connect your power source and then use an ethernet cable to connect the injector to the RouterBOARD device. Helps reducing number of wires

A super low loss 50cm long RPSMA cable for superior connection quality, suited for indoor and outdoor use, this cable provides superior matching and loss values. The name of this cable comes from combining the words “flexible” and “waveguide”

Low-cost passive PoE base unit for powering passive PoE devices over ethernet. Simply connect your power source to the injector, and then use an ethernet cable to connect the injector to the RouterBOARD device. Helps reducing number of wires that lead

You can’t buy safety, but you can buy an RBGESP surge protector and keep your setup safe. RBGESP is Gigabit Ethernet Surge Protector that can be used to protect the network from lightning or surge damages. Here’s what a typical use-case would

48V 2A 96W power supply, to be used with MikroTik products that support 48V POE output, like hEX PoE and CRS112-8P-4S-IN. It’s providing 30% more current than the old model 48POW (48V 1.46A 70W), allowing more power per port. Co

The GPeR unit allows to extend Ethernet cable by additional hop (

U.fl-SMA female pigtail, that can be used to connect your LTE card to an external antenna if you are using wAP R kit (there are special openings in the enclosure of the wAP R, designed for these pigtails)

Professional high-frequency SMASMA cable from MikroTik designed for use in the LTE industry, for example for connecting LTE CPE unit and an LTE antenna. The 1m cable is terminated with two SMA male connectors. For better protection agains

MikroTik UP1302C-12 is a replacement internal power supply that is specially designed for some MikroTik devices. Total power is 130W at 12V and 10.8A max. current. Compatibility list CCR1036-8G-2S+EM (rev. 2) CCR1

Odrušovač pro MikroTik RB wAP snižuje nežádoucí interferenční rušení ze zadní strany a z bočních stran. Ochraňuje signál jen v žádoucí oblasti. Odrušovač spolu se zadním krytem nezvyšuje zisk antény, avšak výrazně snižuje nežádoucí rušení a díky tomu z...

12POW150 is replacement Hot Swap power source for MikroTik CCR1072-1G-8S+. Total output power is 150W.

GESP+POE-IN is a passive Gigabit PoE injector with integrated Ethernet surge protection with one Ethernet port and on the other side is cable with RJ45 connector and ground cable terminated with a loop. This version is intended for indoor use on

Outdoor AC/DC power supply in a durable metal chassis with output voltage 53 V, max. output current 4.7 A, total power 250 W suitable for a series of netPower products from MikroTik. The chassis is IP67 certified with extra protec

DINrail PRO is a mounting bracket for LtAP mini series products, designed to fit standard 35 mm × 7.5 mm DIN rails. This bracket will allow to install LtAP mini next to the industrial control equipment like water meters etc., as well as in equipment ra

±48 V DC telecom Open Frame Power supply with 12 V 8 A output, for use with new “r2” revision of Cloud Core Routers. Simply remove one of the current power supplies and replace with the new PW48V-12V85W for -48 V installations. Compatibility

The GPEN11 is a power injector that can be mounted on a wall, and will power your uplink devices with PoE power. MikroTik GPEN The GPEN11 is part of the GPEN (Giga

The GPEN21 is a smart power injector that serves as an advanced software controlled repeater. Not only can it power your uplink devices via PoE, it can also provide a range of useful software features: Interface mana

A very elegant metal and easily mountable mounting frame from MikroTik, size 19" with height 10U is suitable for laboratory tables, exhibitions or demonstrations. It is not new and revolutionary product, it is more of a trifle that ca

Rackmount kit RMK-2/10 allows the installation of two smaller MikroTik devices with a width of 200mm in traditional 19 inch data cabinets. Alternatively, you can permanently remove the longer part from both brackets and install only o

Hot-swap 54.5V 10.35A power supply for the CRS320-8P-8B-4S+RM PoE++ switch. The switch comes with a single 600W PSU and an expansion slot for a second PSU that can raise the total power output all the way to 1150 Watts,

Replacement 500 W power supply for MikroTik CRS328-24P-4S+RM PoE switch.

Replacement 750 W power supply for MikroTik CRS354-48P-4S+2Q+RM PoE switch.

The Mikrotik GPER14i is a manageable outdoor PoE extender, perfect for extending power to your outdoor devices such as Wi-Fi access points and IP cameras. It features 4x Gigabit LAN ports, with 1 port supporting PoE-IN (802.3bt, 90W) and

CCR2004-16G-2S+ comes with two hot-swap dual redundant power supplies. If one of them goes out of order at some point, the other one will take over. Then you can use this kit to replace the old power supply – and you don’t even have t

Be prepared for the unexpected with the backup hot-swappable fans for our newest devices, such as the flagship CCR2216! If your fans go out of order at some point, you can swap them without unnecessary downtime, as there is no need to turn the router o

A white power adapter with direct installation into a socket with an output voltage of 5V DC, a maximum current of 2.4A, a total output power of 12W and a USB-C connector. The input plug to the socket is EU type.

Outdoor AC/DC power supply in a durable metal chassis with output voltage 26 V, max. output current 9.4 A, total power 250 W suitable for a series of netPower products from MikroTik. The chassis is IP67 certified with extra protec

nRayAIM-DH1 is an alignment and aiming attachment for the nRAY. Use it to attach a scope of your choice for even greater precision and easier installation of the Wireless Wire nRAY. *Scope is not included.

Power adapter with output voltage 48V DC, maximum current 0.95A, total output power 45,6W and connector 5.5 / 2.1mm. The power source is part of the MikroTik GPEN concept, which provides all the benefits of GPON.

Power adapter with output voltage 57V DC, maximum current 0.8A, total output power 45,6W and connector 5.5 / 2.1mm. The power source is part of the MikroTik GPEN concept, which provides all the benefits of GPON.