Accessories

The new MikroTik Gigabit PoE adapter for powering any RouterBOARD over Gigabit Ethernet. Simply connect your power source and then use an ethernet cable to connect the injector to the RouterBOARD device. Helps reducing number of wires

Low-cost passive PoE base unit for powering passive PoE devices over ethernet. Simply connect your power source to the injector, and then use an ethernet cable to connect the injector to the RouterBOARD device. Helps reducing number of wires that lead

Original MikroTik power adapter with direct installation in a socket with a standard 5.5 / 2.1mm connector designed for powering, for example MikroTik devices with input voltage 24V DC. The power adapter has a maximum power 19W and

48V 2A 96W power supply, to be used with MikroTik products that support 48V POE output, like hEX PoE and CRS112-8P-4S-IN. It’s providing 30% more current than the old model 48POW (48V 1.46A 70W), allowing more power per port. Co

GESP+POE-IN is a passive Gigabit PoE injector with integrated Ethernet surge protection with one Ethernet port and on the other side is cable with RJ45 connector and ground cable terminated with a loop. This version is intended for indoor use on

U.fl-SMA female pigtail, that can be used to connect your LTE card to an external antenna if you are using wAP R kit (there are special openings in the enclosure of the wAP R, designed for these pigtails)

Odrušovač pro MikroTik RB wAP snižuje nežádoucí interferenční rušení ze zadní strany a z bočních stran. Ochraňuje signál jen v žádoucí oblasti. Odrušovač spolu se zadním krytem nezvyšuje zisk antény, avšak výrazně snižuje nežádoucí rušení a díky tomu z...

MikroTik power adapter with 5V voltage, maximum current 1A, max. Power 5W and microUSB connector. This power source is suitable, for example, for MikroTik hAP mini, hAP lite and cAP lite.

RBGPOE-CON-HP serves as a converter of any 48V PoE source (passive PoE, Telecom PoE, 802.3af and 802.3at) to passive 24V PoE, for example for powering RouterBOARD devices. The PoE converter supports 10/100/1000Mbps. The maximum output power is 24W.

±48 V DC telecom Open Frame Power supply with 12 V 8 A output, for use with new “r2” revision of Cloud Core Routers. Simply remove one of the current power supplies and replace with the new PW48V-12V85W for -48 V installations. Compatibility

Rackmount kit RMK-2/10 allows the installation of two smaller MikroTik devices with a width of 200mm in traditional 19 inch data cabinets. Alternatively, you can permanently remove the longer part from both brackets and install only o

The Mikrotik GPER14i is a manageable outdoor PoE extender, perfect for extending power to your outdoor devices such as Wi-Fi access points and IP cameras. It features 4x Gigabit LAN ports, with 1 port supporting PoE-IN (802.3bt, 90W) and

The GPeR unit allows to extend Ethernet cable by additional hop (

The Sleeve30 kit for mANT30 parabolic antenna will enhance point-to-point link performance by reducing noise and will also reduce impact on adjacent RF devices by removing the side radiation from the antenna. Sleeve30 Kit also reduces

We are now offering a Hot Swap -48V DC telecom power supply (product code PW48V-12V150W), available to purchase separately for use with CCR1072. Simply remove one of the current power supplies and replace with the new PW48V-12V150W for -48V installatio

MikroTik 24V2APOW is a replacement internal power supply that is specially designed for some MikroTik devices. Total power is 60W at 24V and 2.5A max. current. Compatibility with these models CCR1009-7G-1C-1S+ CRS31

Cable reduction from MMCX to RSMA female, 26 cm long, intended for the frequency band from 2 to 6 GHz. The MMCX connector is angled and the RSMA female is straight. This is a high-quality connection, e.g. in BaseBox2 or BaseBox5 devic

Professional high-frequency SMASMA cable from MikroTik designed for use in the LTE industry, for example for connecting LTE CPE unit and an LTE antenna. The 1m cable is terminated with two SMA male connectors. For better protection agains

12POW150 is replacement Hot Swap power source for MikroTik CCR1072-1G-8S+. Total output power is 150W.

MikroTik UP1302C-12 is a replacement internal power supply that is specially designed for some MikroTik devices. Total power is 130W at 12V and 10.8A max. current. Compatibility list CCR1036-8G-2S+EM (rev. 2) CCR1

Power adapter with output voltage 57V DC, maximum current 0.8A, total output power 45,6W and connector 5.5 / 2.1mm. The power source is part of the MikroTik GPEN concept, which provides all the benefits of GPON.

DINrail PRO is a mounting bracket for LtAP mini series products, designed to fit standard 35 mm × 7.5 mm DIN rails. This bracket will allow to install LtAP mini next to the industrial control equipment like water meters etc., as well as in equipment ra

nRayAIM-DH1 is an alignment and aiming attachment for the nRAY. Use it to attach a scope of your choice for even greater precision and easier installation of the Wireless Wire nRAY. *Scope is not included.

The GPEN21 is a smart power injector that serves as an advanced software controlled repeater. Not only can it power your uplink devices via PoE, it can also provide a range of useful software features: Interface mana

Power adapter with output voltage 48V DC, maximum current 0.95A, total output power 45,6W and connector 5.5 / 2.1mm. The power source is part of the MikroTik GPEN concept, which provides all the benefits of GPON.

MikroTik GB60A-S12 is a replacement internal power supply that is specially designed for some MikroTik devices. Total power is 60W at 12V and 5A max. current. Compatible with CCR1016 r2 models

Hot-swap 54.5V 10.35A power supply for the CRS320-8P-8B-4S+RM PoE++ switch. The switch comes with a single 600W PSU and an expansion slot for a second PSU that can raise the total power output all the way to 1150 Watts,

Replacement 500 W power supply for MikroTik CRS328-24P-4S+RM PoE switch.

Replacement 750 W power supply for MikroTik CRS354-48P-4S+2Q+RM PoE switch.

Outdoor AC/DC power supply in a durable metal chassis with output voltage 26 V, max. output current 9.4 A, total power 250 W suitable for a series of netPower products from MikroTik. The chassis is IP67 certified with extra protec